
PPE Is the Last Resort: General Rules and Care of Protective Equipment
What You’ll Learn
- The general rule of 130.7(A): who must be provided PPE, and how it must be matched to the body part and the work
- Why PPE sits at the bottom of the hierarchy of risk control — and what “protection” realistically means
- What PPE does not protect against: arc blast and physical trauma
- The employer’s duty to verify that issued PPE actually meets the applicable standards
- The care rules of 130.7(B): inspection before each use, proper storage, and laundering that does not quietly destroy protection
The Last Line of Defense, Not the First Plan
Personal protective equipment is where the hierarchy of risk control ends. Elimination — placing equipment in an electrically safe work condition — is the primary method of protection, and every other control is preferred before PPE. When an employer defaults to PPE as the protection method for a task, that choice carries an admission: no higher control could be used to lower the hazard further. Under no circumstances does the availability of PPE justify energized work, and PPE never prevents an incident — an arc happens or it does not, regardless of what the worker is wearing.
What PPE does is limit the consequences. Properly selected arc flash PPE can reduce a burn injury to one that is survivable and recoverable, but it does not promise an uninjured worker: the testing behind arc ratings is built around a 50 percent probability of protection from a second-degree burn at the rated energy. The requirements of 130.7 apply regardless of which risk assessment method — incident energy analysis or PPE category — was used to select the gear.
The General Rule: Provided, Used, and Matched to the Body and the Task
The general rule of 130.7(A) is one sentence with three working parts. Employees exposed to electrical hazards, when the risk associated with that hazard is not adequately reduced by the applicable electrical installation requirements, shall be provided with — and shall use — protective equipment that is designed and constructed for the specific part of the body to be protected and for the work to be performed.
Each part matters. The duty is triggered by exposure the installation itself does not adequately control, not by the employer’s convenience. The equipment must actually be used, not merely issued and left in the gang box. And the match is specific twice over: the gear is designed for the body part at risk — hands, face, head, torso, whole body — and for the work being performed, judged against the hazards the risk assessments identified. An analysis of the task identifies each hazard, the body parts inside the relevant boundary, and the severity, then compares that exposure against what the selected PPE offers. Where only the face is inside the arc flash boundary, a rated hard hat and face shield combination answers the exposure; where the whole head is inside the boundary, an arc flash hood or a face shield with an arc-rated balaclava is required. The PPE requirements of 130.7 are intended to protect a person from arc flash and electric shock hazards — and all parts of the body inside the arc flash boundary must be protected, not just the obvious ones.
Gear can also serve two hazards at once. Rubber insulating gloves with protectors are the standard example: they provide electric shock protection for the hands and forearms and, at the same time, some degree of arc flash protection. Dual service is common, but it is never assumed — it is confirmed against both hazards.
Verified, Not Just Issued
Providing PPE means providing compliant PPE. The employer must verify that the gear supplied conforms to the applicable protective equipment standards — the consensus standards collected in the informational note tables to 130.7(C)(14) and 130.7(E). Verification by test is generally the only reliable way to know a material will perform as expected, and equipment that has not been adequately tested might provide less protection than expected — or, in some cases, actually increase the severity of an injury during an incident. Substandard or counterfeit gear is not a bargain; it is a hazard issued as protection.
A garment’s own sewn-in label is not necessarily sufficient proof. Some standards evaluate only the fabric a garment is made from, not the finished shirt or pants sewn from it, so confirming the rating means confirming that the correct standard was applied to the product as purchased — fabric and finished garment alike. That confirmation is the employer’s responsibility.
What PPE Does Not Protect Against
PPE has no arc blast rating. The requirements of 130.7 address the thermal effects of an arc flash and protection against electric shock. They do not address protection against physical trauma. An arcing fault converts electrical energy explosively — metal vaporizes and expands, a pressure wave develops, and the event can hurl a door or panel into a worker, knock a worker off a ladder or out of a bucket, or eject shrapnel at extreme speed. Pressures in severe events can reach levels known to damage lungs, and sound levels can exceed the threshold for permanent hearing damage. Arc-rated clothing and shock protection may leave the thermal and shock exposure survivable while doing nothing at all about the blast that throws the worker across the room.
This limit matters for planning, not just for honesty. An employer who authorizes energized work must consider the injuries the standard’s PPE is not designed to prevent, and decide what other methods protect the employee against them — distance, barriers, remote operation, or not doing the work energized at all. PPE answers the hazards it is rated for. It is silent on the rest.
Care of Equipment: Safe, Clean, and Reliable
Care of equipment under 130.7(B) begins with the general duty: protective equipment shall be maintained in a safe, clean, and reliable condition, in accordance with the manufacturers’ instructions. PPE lives a working life of donning and doffing, cleaning and laundering, and every cycle either preserves its protection or erodes it. The manufacturer’s instructions are the baseline for that maintenance because they are written for the specific materials and construction of the gear.
Responsibility for care follows the employer’s responsibility for protection: employers need policies and procedures for maintaining equipment regardless of who performs the maintenance. Some gear, like an arc-rated suit, may be purchased and maintained by the employer; everyday arc-rated shirts and pants may be maintained by the employee. Either way, the standard of care does not change with the arrangement — and where employees provide their own equipment, the employer remains responsible for assuring its adequacy, maintenance, and sanitation.
Inspect Before Each Use
Visual inspection before each use is a hard requirement, not a habit to encourage: protective equipment shall be visually inspected before each use. The inspection is the last chance to catch the damage that use, storage, and laundering cause — rips and tears (which must be properly repaired, not sewn shut with whatever thread is at hand), contamination, worn or holed fabric, cracked or cut gloves. Periodic electrical testing required elsewhere in 130.7 for items such as rubber insulating equipment runs on its own schedule; the before-use visual inspection happens every time, on top of it. Gear that fails inspection comes out of service until it is repaired or replaced — it is not worn “one more time.”
Storage: Away from Damage, Moisture, and Dust
Storage is prescribed just as directly: protective equipment shall be stored in a manner to prevent damage from physically damaging conditions and from moisture, dust, or other deteriorating agents. A glove set crushed under tools in a truck box, clothing left damp in a locker, gear stored where sunlight, solvents, or sharp edges reach it — each is a slow failure applied between uses. Storage is part of protection because deterioration is invisible at the moment it happens and visible only at the moment the gear is called on — which is the worst moment to discover it. Bags, cabinets, and dedicated storage that keep gear clean, dry, and physically protected are how the requirement is met in practice.
Laundering: Cleaning That Can Destroy Protection
Laundering is where well-intentioned care most often defeats itself. Contaminated gear can be prone to catastrophic failure in an arc event, so cleaning is necessary — but laundering done in the wrong cycle, at the wrong temperature, or with the wrong detergent can strip or damage the very properties the rating depends on, leaving clothing that looks clean and protects less than its label claims. Guidance exists precisely because the details matter: ASTM F1449 covers industrial laundering of flame, thermal, and arc resistant clothing, and ASTM F2757 covers home laundering — together they address acceptable cleaning agents, whether bleach-type additives may be used, suitable processes, and water temperatures. The employer must decide whether gear is commercially or home laundered and set the procedure accordingly. One more rule follows from sharing: if arc-rated PPE is shared between employees, it must be cleaned between uses, for sanitation as well as condition.
Worked Scenario
A utility contractor issues daily-wear arc-rated shirts and pants, a switching suit, and rubber glove kits. The program looks complete on paper. In practice, three care failures are quietly running at once. The shirts go home with the crew and are washed in hot water with bleach additive and fabric softener, cycle after cycle — the fabric’s arc performance is degrading invisibly, with no tear or stain to announce it. The glove kits live loose in a truck tool bin, where a wrench edge has nicked one glove’s cuff. And the shared switching suit hangs in a damp corner of the substation control house, unwashed after its last use, picking up contamination and mildew.
The before-use inspection catches exactly one of the three: the nicked glove, pulled from service at the morning check — the system working as designed. The other two failures are invisible until the day the suit and shirts are asked to perform. When an arc event occurs during switching, the contaminated suit underperforms and the degraded shirt offers less than its rating; the crew member’s burns are worse than the risk assessment predicted — not because the wrong PPE was selected, but because the right PPE was cared for wrongly. The investigation’s conclusion writes the lesson plainly: selection is half the program. Inspection before each use, protected storage, and laundering by the book are the other half.
Common Mistakes and Safety Notes
- Treating PPE as the plan instead of the last resort. Placing equipment in an electrically safe work condition is the primary protection; PPE is what remains when higher controls cannot eliminate the hazard, and it never justifies energized work.
- Expecting PPE to stop an incident. PPE limits injury severity; it does not prevent the arc, and at its rating it is tested around a 50 percent probability of preventing a second-degree burn.
- Forgetting the blast. PPE carries no arc blast rating and does not protect against physical trauma — pressure waves, flying panels, and falls must be controlled by other means.
- Issuing gear without verifying it. Confirm the supplied PPE conforms to the applicable consensus standards; a fabric rating or a garment label alone may not prove the finished product was tested.
- Skipping the before-use look. Visual inspection before each use is required — damaged, contaminated, or torn gear comes out of service until properly repaired or replaced.
- Storing gear where it deteriorates. Moisture, dust, crushing loads, and other damaging conditions destroy protection between uses; store gear to prevent exactly that.
- Laundering by guesswork. Wrong cycle, temperature, or detergent — including bleach-type additives where prohibited — can silently reduce arc performance. Follow the manufacturer’s instructions and the ASTM laundering guides.
- Sharing PPE without cleaning it. Shared arc-rated equipment must be cleaned between uses.
Summary
Section 130.7(A) requires that employees exposed to electrical hazards — where the risk is not adequately reduced by the applicable installation requirements — be provided with, and use, protective equipment designed and constructed for the specific part of the body to be protected and for the work to be performed. That protection targets arc flash and electric shock: correctly selected, it makes burn injury reduced and survivable, but it prevents nothing, carries no arc blast rating, and offers no protection against physical trauma. The employer must verify that issued PPE conforms to the applicable consensus standards, not merely that it was purchased. Section 130.7(B) then keeps the gear worthy of its rating: maintained in a safe, clean, and reliable condition according to the manufacturers’ instructions, visually inspected before each use, stored so it is protected from physically damaging conditions, moisture, dust, and other deteriorating agents, and laundered with the cycle, temperature, and agents its protection can survive — because PPE, the last resort, only works if it has been cared for like the last resort it is.
Quick-Check Questions
- What does 130.7(A) require protective equipment to be designed and constructed for?
Answer: The specific part of the body to be protected and the work to be performed. - What two hazards are the PPE requirements of 130.7 intended to protect against?
Answer: Arc flash and electric shock hazards. - Name two things PPE does not protect against.
Answer: Arc blast effects and physical trauma (such as being thrown by a pressure wave or struck by flying equipment parts) — 130.7 addresses thermal effects and shock, not trauma. - When must protective equipment be visually inspected?
Answer: Before each use. - What storage conditions must be prevented for protective equipment?
Answer: Damage from physically damaging conditions and from moisture, dust, or other deteriorating agents — the equipment must be stored so it stays safe, clean, and reliable.
Based on NFPA 70E (2024), Article 130, paraphrased for study.
Video lesson for this module is in production — coming soon.
Quiz for this module is being prepared.
Flashcards for this module are being prepared.



