
What You’ll Learn
- Why job briefings are a required element of the employer’s documented electrical safety program — not an optional habit
- Who leads the briefing, when it happens, and the six subject areas it must cover
- The difference between Annex I’s two checklists: job safety planning (before the job) and the job briefing (with the crew)
- Why the sample checklists are a floor, not a ceiling — and why circumstances can demand more than the list
A Conversation Before the Work, Not After the Accident
Most electrical accidents are not caused by a hazard nobody knew about. They happen when one person on the crew knew — or should have known — and the knowledge never reached the rest of the team. Informative Annex I exists to close that gap. It supports the job briefing: a short, structured conversation held before a job begins, led by the employee in charge, in which the hazards of the job and the controls for them are put in front of every employee who is about to do the work. The annex supplies two sample checklists — one for planning the job safely, one for briefing the crew — and an introduction that ties both to the employer’s larger safety program. Annex I is informative guidance, not a requirement in itself, but the briefing it supports is anything but optional.
Part of the Program: The 110.3(A) Duty
Job briefings are an element of the employer’s electrical safety program. Section 110.3(A) requires the employer to implement and document an overall electrical safety program (ESP), and job briefings must be included among the ESP’s elements. That framing matters. A briefing is not a courtesy the foreman extends when the schedule allows; it is one named component of a documented program the employer is required to maintain. When the briefing is skipped, the gap is not just a missed conversation — it is a missing piece of the program itself, and the annex’s checklists are built to help make sure that piece is actually delivered, job after job.
Led by the Employee in Charge, Before Each Job
The employee in charge conducts the job briefing, and the timing is fixed: before starting each job, and before employees begin the work tasks. Three facts follow from that placement. First, the responsibility has a name — the person in charge of the job owns the briefing; it does not float to whoever feels like talking. Second, the briefing is per job, not per shift, per week, or per project: a new job means a new briefing, because a new job means new hazards, new procedures, or a new crew. Third, the briefing happens before work starts, while there is still time to change the plan — a briefing held after the covers are off is a report, not a control.
What the Briefing Must Cover
The briefing’s coverage is defined by the introduction: it must address the hazards associated with the job, the work procedures involved, special precautions, energy source controls, PPE requirements, and information on the energized electrical work permit. Read that list as the shape of a good five minutes. The hazards name what can hurt the crew on this specific job. The work procedures establish how the task will actually be performed. Special precautions catch the things this job has that routine jobs do not. Energy source controls answer where the energy is and how it is controlled. PPE requirements state what each person wears and why. And the permit information connects the briefing to the energized work permit whenever the job involves one — so nobody learns about the permit’s conditions after the work has already begun.
Two Checklists, Two Moments: Planning and Briefing
Annex I provides two checklists, and they serve two different moments in the life of a job. The job safety planning checklist, Figure I.2, belongs to the planning stage — before the job. It contains examples of items that must be addressed during job planning, and it can help when documenting the hazards and the appropriate protection necessary: the thinking work, done in advance, that decides what the job’s hazards are and how they will be controlled. The job briefing checklist, Figure I.1, belongs to the briefing itself — with the crew, at the point of work. It contains examples of subjects that should be discussed during the job briefing, and it can help facilitate the conversation the employee in charge leads. Planning decides; briefing communicates. A crew can be handed a well-planned job and still be unbriefed, or sit through a briefing for a job nobody actually planned — the annex keeps the two steps separate because each one fails in its own way.
Examples, Not a Ceiling
Both checklists carry the same warning: they are not all-inclusive. The figures contain examples of items and subjects — starting points that cover what jobs commonly need, not a complete universe of what any particular job might require. The introduction is explicit that other subjects might need to be considered based on specific circumstances. Job planning, for instance, should include identifying the proper practices and procedures for an assigned task — and a job with unusual equipment, an unusual environment, or an unusual crew may need planning and briefing subjects that appear on no sample list. The checklist disciplines the conversation; it does not excuse the planner or the briefer from thinking past it.
Worked Scenario
A two-person crew is assigned to replace a failed breaker in a motor control centre that will remain partly energized, under an energized electrical work permit. The employee in charge plans the job first, working through the job safety planning checklist: the hazards are documented — the energized bus in the same enclosure, the adjacent live sections — and the appropriate protection is decided, including the PPE and the approach boundaries. Then, before any tool comes out, she briefs her partner using the job briefing checklist to structure the conversation: the hazards associated with this job, the procedure they will follow step by step, the special precaution that the section to the left stays live, how the energy sources are controlled, the PPE each of them will wear, and the conditions written into the energized work permit. The briefing takes minutes. During it, her partner raises a point the plan had missed — the replacement breaker’s terminals sit closer to the live bus than the old one’s did — and the procedure is adjusted before the work starts, not discovered during it. That adjustment is the briefing doing exactly the job Annex I built it for.
Common Mistakes and Safety Notes
- Treating the briefing as optional. Job briefings must be included among the elements of the employer’s documented electrical safety program under 110.3(A) — they are a program requirement, not a courtesy.
- Briefing once per project. The briefing is conducted before starting each job, before employees begin the work tasks. A new job gets a new briefing.
- Letting anyone — or no one — lead it. The employee in charge conducts the briefing. Ownership is assigned, not assumed.
- Confusing planning with briefing. The Figure I.2 planning checklist supports documenting hazards and protection in advance; the Figure I.1 briefing checklist supports the conversation with the crew. One does not replace the other.
- Reading the checklist as complete. The sample checklists are examples, not an all-inclusive list — specific circumstances can require subjects beyond them.
- Skipping the permit. Information on the energized electrical work permit is one of the subjects the briefing must cover whenever the job involves one.
Summary
Informative Annex I supports the job briefing: a required element of the employer’s documented electrical safety program under 110.3(A), conducted by the employee in charge before starting each job and before employees begin the work tasks. The briefing covers the hazards associated with the job, the work procedures involved, special precautions, energy source controls, PPE requirements, and information on the energized electrical work permit. The annex’s two sample checklists serve two distinct moments — the Figure I.2 job safety planning checklist, for documenting hazards and the appropriate protection during planning, and the Figure I.1 job briefing checklist, for facilitating the conversation with the crew. Neither list is all-inclusive: they are examples, and the circumstances of a specific job can always demand more.
Quick-Check Questions
- Who conducts the job briefing, and when?
Answer: The employee in charge, before starting each job — the briefing must be performed before employees begin the work tasks. - What six subject areas must the briefing cover?
Answer: The hazards associated with the job, the work procedures involved, special precautions, energy source controls, PPE requirements, and information on the energized electrical work permit. - What is the difference between the Figure I.1 and Figure I.2 checklists?
Answer: Figure I.1 is the job briefing checklist — examples of subjects to discuss with the crew during the briefing. Figure I.2 is the job safety planning checklist — examples of items to address during job planning, helpful for documenting hazards and the appropriate protection. - Where does the job briefing requirement sit in the employer’s obligations?
Answer: Job briefings must be included among the elements of the overall electrical safety program the employer is required to implement and document under 110.3(A). - Are the annex’s checklists complete lists of everything a job might require?
Answer: No. They contain examples and are not intended to be all-inclusive — other subjects might need to be considered based on specific circumstances.
Based on NFPA 70E (2024), Informative Annex I, paraphrased for study.
Video lesson for this module is in production — coming soon.
Quiz for this module is being prepared.
Flashcards for this module are being prepared.



