
What you’ll learn
After this post, you will be able to identify a diagram as schematic, one-line, block, or wiring; define resistivity, temperature coefficient of resistance, closed circuit, open circuit, short circuit, series circuit, parallel circuit, and equivalent resistance; and determine whether a circuit is open or closed.
The words before the arithmetic
Before you calculate anything in a DC circuit, you need the vocabulary: the four ways to draw a circuit, the two numbers that describe how a real wire behaves, and the words that say whether a circuit is complete, broken, or dangerously shorted. This chapter is that vocabulary.
Four ways to draw a circuit
- Schematic diagram: the standard way to communicate electrical and electronic circuits. Components appear as graphic symbols, compact, showing connections and relationships, traceable from input to output. The handbook’s example is a two-transistor radio circuit, read left to right from radio waves to sound. Widely used in construction, maintenance, and servicing.
- One-line (single-line) diagram: components shown by single lines and symbols. One line represents two or more conductors between components. It gives the sequence and the pertinent information with less detail than a schematic, and is used for highly complex systems without showing physical connections or individual conductors. The handbook’s example is an electrical substation.
- Block diagram: shows the relationship between component groups or stages, with the path from input to output — the flow of a signal or of power through a system. The handbook’s examples are a power supply and a control circuit. You use it to understand a system before you trace its detail.
- Wiring diagram: the simplest view of wiring connections, easy to follow. Components appear in pictorial form, located where they actually sit in the equipment. It is sometimes called a pictorial diagram. It is what you follow when you actually wire up part of a system.
Rule of thumb: schematic for detail, one-line for big systems, block for stages, wiring for actual hookup. Learn to sort a diagram by its job, not by how pretty it is.
Resistivity: the material’s own resistance
Resistivity, given the symbol ρ (rho), is a measure of the resistance a material imposes on current. It is a property of the material itself — given the conductor’s length and cross-sectional area, knowing its resistivity lets you calculate its resistance. Resistivity has units of ohm-metres in the metric system. The chipmaker formula R = ρ × L / A, with L = length and A = cross-sectional area, gives the numbers. Example: copper’s resistivity is about 1.7 × 10-8 ohm-metres. The handbook’s examples include a calculation of the resistance of a copper wire of given length and cross-sectional area, worked step by step with ohm-metres so that units cancel cleanly.
Temperature coefficient: hot wires change resistance
The temperature coefficient of resistance, α (alpha), is the change in resistance per given temperature change, in ohms per ohm per degree Celsius. The value for copper at 20°C is 0.00394 per °C. The handbook’s worked example uses that coefficient to find the resistance of a copper winding as it warms up from 20°C to 75°C: it rises from 20 ohms to about 24.3 ohms. The formula for a small temperature change is Rt = R20 × [1 + α × (t — 20)]. It is not a formula to memorize, but the fact that hotter copper has more resistance is something every electrician needs to know.
The four parts of a circuit, and what can go wrong with them
An electric circuit has at least four basic parts: an EMF source, conductors, load or loads, and a control or switching device. A simple circuit with those four parts — a battery, a switch, a connecting conductor, and a load, say a light bulb — is the model for everything in this module. A circuit can fail in only a few ways:
- Closed circuit: an uninterrupted path from source through load and back to source. Current flows. This is normal operation.
- Open (incomplete) circuit: a break prevents a complete current path. No current flows.
- Short circuit: a path offering very little resistance, causing dangerously high current. Usually caused by insulation failure or a wrong connection — the word short means the current takes a shortcut, bypassing most of the load.
- Series circuit: only one path for current. The current is the same throughout — through the first component, then the second, then the third. The voltage drops add up to the supply voltage.
- Parallel circuit: two or more components across the same voltage source. Each branch has its own current; the source current is the sum of the branch currents. The equivalent resistance is less than that of any single branch resistor.
- Equivalent resistance: the total resistance of parallel resistors as seen by the source. It is a value less than that of any single branch resistor, and it is the value you use when calculating total circuits.
Common mistakes
- “Resistivity and resistance are the same thing.” They are not. Resistivity is a property of the material, measured in ohm-metres; resistance is a property of a particular piece of wire, measured in ohms.
- “A short circuit is just a circuit that does not work.” It is worse than that: a short offers very low resistance, so the current is dangerously high. A fuse or breaker must protect it.
- “Equivalent resistance of parallel resistors is bigger than the branches.” It is always smaller than the smallest branch. Parallel paths let more current flow.
- “A wiring diagram and a schematic are interchangeable.” They are not. A schematic shows how a circuit works; a wiring diagram shows where to connect the wires. Use the schematic to understand, the wiring diagram to build.
Summary
Four diagrams: schematic for detail, one-line for big systems, block for stages, wiring for hookup. Resistivity is a material property; resistance is a piece of wire. Heat raises the resistance of copper. A closed circuit flows, an open circuit stops, a short circuit burns, and parallel resistors behave as a smaller single resistance.
Quick-check questions
- Which diagram type would you use to understand how a circuit works, and which to wire it up?
- What is resistivity, and how does it differ from resistance?
- Copper has a temperature coefficient of 0.004 per degree Celsius. Does a hot copper winding have more or less resistance than a cold one?
- What is a short circuit, and why is it dangerous?
- Is the equivalent resistance of parallel resistors larger or smaller than any single branch resistor?
Answers: 1. A schematic diagram to understand how it works; a wiring diagram to wire it up. 2. Resistivity is a property of the material itself — its own resistance per unit length and area — while resistance is a property of a particular piece of wire made from that material. 3. More: the resistance of copper increases with temperature. (α is positive.) 4. A path offering very little resistance, so the current is dangerously high; it can cause fire or equipment damage. 5. Smaller.
Based on DOE-HDBK-1011/92, Electrical Science, Module 2, paraphrased for study.



