
What you’ll learn
After this post, you will be able to list the four ways to produce a DC voltage, state the purpose of a rectifier, and describe the outputs of a half-wave rectifier and a full-wave bridge rectifier.
Four ways to get DC
Every DC circuit in this module starts at a source, and the handbook names four of them: batteries, DC generators, thermocouples, and rectifiers. They make DC in completely different ways, and the diode section — the heart of this chapter — is the one you will use most in electronics.
1. Batteries: chemistry in a cell
A battery is two or more chemical cells in series, converting chemical energy to electrical energy. A cell is two electrodes of different metals or compounds sitting in an electrolyte. The electrolyte ionises into positive and negative ions. Chemical action ionises atoms in one electrode, depositing electrons on it so it becomes negative, while positive ions enter the electrolyte. Positive ions from the electrolyte are repelled to the other electrode, where they combine with electrons, removing electrons so that electrode becomes positive. The full treatment of battery types and hazards is deferred to Module 4.
2. DC generators: a coil, a field, and a commutator
The simplest DC generator is a single-turn armature coil cutting a magnetic field. The coil alone would produce alternating voltage, but the commutator fixes that: after a half-turn, the commutator segments swap brushes, so the side of the coil contacting either brush is always cutting the field in the same direction. The brushes keep constant polarity, and the output is pulsating DC — bumpy, not smooth. The full treatment of generator types and ratings is deferred to a later module.
3. Thermocouples: heat at a junction
A thermocouple is two different metals joined at a junction. Heating the junction frees electrons in one metal more than in the other, so a voltage appears across the junction; the hotter the junction, the higher the voltage. Its everyday use is measuring temperature: attach a meter, read the voltage, and you have the temperature. It is a power source in the strict sense, but a weak one, and the handbook uses it mainly as an instrument.
4. Rectifiers: turning AC into DC
Most generating stations produce AC, because AC transfers over long distances with fewer losses than DC. To use that power in a DC circuit, you must rectify it — change AC to DC. The workhorse for that job is the diode: a semiconductor device that allows current to flow in one direction only. Its symbol is a triangle pointing at a bar. The side at the triangle is the anode; the side at the bar is the cathode. Forward current enters the anode and leaves the cathode, following the arrow.
Forward bias: the gate opens
Forward bias means the positive source terminal goes to the anode and the negative terminal to the cathode. The diode conducts, with only a small voltage drop of about 0.7 volts for silicon. It acts like a closed switch in that direction.
Reverse bias: the gate stays shut
Reverse bias means the anode goes to the negative terminal and the cathode to the positive terminal. The diode does not conduct; it behaves like a very high resistance. It is not a perfect open circuit, but for circuit calculations treat it as one. Push the reverse voltage high enough and it breaks down — that is damage, not a feature, in an ordinary rectifier diode.
Half-wave, full-wave, and bridge rectifiers
- Half-wave rectifier: a single diode is alternately forward and reverse biased each AC cycle, so it passes only one half of the input cycle. The output is pulsating DC roughly half of the time.
- Full-wave rectifier: two diodes rectify the entire AC cycle. The output is pulsating DC from both halves, with a lower peak voltage — half the input in the centre-tapped version described.
- Full-wave bridge rectifier: four diodes. Its output is pulsating DC with all input waves transferred; it presents a pulsating DC at higher peaks than the alternatives.
Note the handbook’s own wording: its learning objectives ask for the half-wave and the full-wave bridge rectifier; the four-diode bridge, not the two-diode centre-tapped circuit, is the one to be able to describe. The average output voltage is quoted as about 63.7% of the peak voltage for the half-wave and bridge rectifiers; the half-wave rectifier’s peak output is about 31.8% of the peak input voltage. The handbook gives this as a working rule: for a half-wave rectifier, VDC = 0.318 × VPEAK, and for a full-wave rectifier, VDC = 0.636 × VPEAK. Work the numbers on those rules, not by guessing.
Common mistakes
- “A rectifier output is smooth DC.” It is not. Half-wave, full-wave, and bridge outputs are all pulsating DC, with a ripple that a filter must smooth.
- “A reverse-biased diode is an open circuit.” It blocks current, but only as a high resistance, not as a perfect open circuit — apply enough reverse voltage and it breaks down.
- “A DC generator makes smooth DC.” Its output is pulsating DC, because the commutator only fixes the polarity, not the rise and fall of a rotating coil.
- “A thermocouple is a power source like a battery.” It makes a voltage, but its normal job is measuring temperature. Treat it as an instrument, not a power supply.
Summary
Four ways to produce DC: battery chemistry, a commutated generator, a heated two-metal junction, and rectification. The diode is the key: forward bias lets current through, reverse bias stops it. A half-wave rectifier passes one half-cycle; a full-wave bridge rectifies both, and its average output is higher. None of them gives smooth DC on its own — that needs a filter.
Quick-check questions
- What are the four ways to produce a DC voltage?
- What is the purpose of a rectifier?
- What is forward bias, and does the diode conduct?
- What is the output of a half-wave rectifier?
- How does a full-wave bridge rectifier differ from a half-wave rectifier?
Answers: 1. Batteries, DC generators, thermocouples, and rectifiers. 2. To convert AC power to DC power. 3. Positive terminal to the anode and negative to the cathode, and yes, it conducts. 4. Pulsating DC (VDC = 0.318 × VPEAK). 5. A bridge rectifier rectifies both halves of the AC cycle, while a half-wave rectifier passes only one half-cycle.
Based on DOE-HDBK-1011/92, Electrical Science, Module 2, paraphrased for study.



