
Rubber Insulating Gloves: Classes, Voltage Limits, and Test Intervals
What You’ll Learn
- When rubber insulating gloves are worn with protectors — and when rubber insulating sleeves join them
- The three conditions that allow gloves to be used without protectors, and the voltage derating that comes with it
- Table 130.7(C)(7)(a): the six glove classes, their maximum ac and dc use voltages, and the minimum protector cuff distances
- The daily routine: inspection before each day’s use, plus an air test for the gloves
- Table 130.7(C)(7)(b): test intervals — gloves every 6 months, blankets and sleeves every 12 months, covers and line hose when their insulating value is suspect
A Rated Barrier You Carry on Your Hands
Section 130.7(C)(7) covers hand and arm protection in four parts: (a) electric shock protection, (b) arc flash protection, (c) maintenance and use, and (d) periodic electrical tests. The glove system has two layers with two different jobs. The rubber insulating glove is the electrical barrier, rated for a specific maximum voltage. The protector — a leather glove worn over the rubber — is the mechanical barrier, shielding the rubber from cuts, punctures, and abrasion that would silently destroy its insulating value. Everything in this article hangs off those two layers, two tables, and one daily habit.
Gloves With Protectors: The Default for Shock Protection
Rubber insulating gloves with protectors are the default under 130.7(C)(7)(a): employees shall wear them where there is a danger of hand injury from electric shock due to contact with exposed energized electrical conductors or circuit parts. The rubber insulating gloves shall be rated for the voltage for which the gloves will be exposed — the glove’s rating must stand up to the voltage the hand can actually meet, which is why the class table below is a selection tool, not a formality.
Notice the structure of the rule: the protector is part of the requirement, not an accessory. Rubber alone insulates well but damages easily, and a glove with an undetected nick or pinhole is worse than no glove at all, because the worker trusts it. The protector keeps the barrier intact between the daily inspections and tests that verify it.
Sleeves: When the Forearm Can Reach the Hazard
Rubber insulating sleeves join the gloves when the exposure goes past the hand: employees shall wear rubber insulating gloves with protectors and rubber insulating sleeves where there is a danger of hand and arm injury from electric shock due to contact with exposed energized electrical conductors or circuit parts. If the forearm can brush a second phase or a grounded surface while the hand is working, the arm needs the same rated barrier as the hand.
Sleeves are classified on the same scale as gloves — the heading of Table 130.7(C)(7)(a) reads “Class Designation of Glove or Sleeve.” One caution from the commentary: sleeves must not be shortened or rolled up, because that would expose skin or flammable undergarments — a rolled sleeve defeats the very coverage it was issued for.
Gloves Without Protectors: Three Conditions and a Derating
Gloves used without protectors are an exception, not an option of convenience. Section 130.7(C)(7)(a) permits rubber insulating gloves to be used without protectors only under all of the following conditions:
- No damaging activity. There shall be no activity performed that risks cutting or damaging the glove.
- Retest before reuse. The rubber insulating gloves shall be electrically retested before reuse.
- Derating. The voltage rating of the rubber insulating gloves shall be reduced by 50 percent for class 00 and by one whole class for classes 0 through 4.
The derating is the price of the missing mechanical protection, and it changes what the glove may be used on. A class 00 glove, normally good for 500 volts ac, drops to a 250-volt ac maximum without its protector. A class 0 glove drops one whole class and is treated as a class 00 — 500 volts ac maximum. A class 2 glove used without protectors is treated as a class 1, with a 7,500-volt ac ceiling. Crews who reach for bare rubber “for the dexterity” without applying the derating are working with a rating the standard has already taken away — and the retest condition means those gloves do not go back into the kit afterward until they have been electrically retested.
The Class Table: Maximum Use Voltages and Cuff Distances
Table 130.7(C)(7)(a) sets the ceiling for every class. “Maximum use voltage” is the highest voltage the glove or sleeve may be exposed to — the class is selected so that this ceiling is at or above the actual exposure:
| Class | Maximum ac use voltage (rms) | Maximum dc use voltage (avg) | Minimum distance, protector cuff to glove cuff |
|---|---|---|---|
| 00 | 500 V | 750 V | 13 mm (0.5 in.) |
| 0 | 1,000 V | 1,500 V | 13 mm (0.5 in.) |
| 1 | 7,500 V | 11,250 V | 25 mm (1 in.) |
| 2 | 17,000 V | 25,500 V | 51 mm (2 in.) |
| 3 | 26,500 V | 39,750 V | 76 mm (3 in.) |
| 4 | 36,000 V | 54,000 V | 102 mm (4 in.) |
The last column belongs with 130.7(C)(7)(c) below: the top of the cuff of the protector glove shall be shorter than the rolled top of the cuff of the insulating glove by at least the distance given for the class — 13 mm for the low classes, growing to 102 mm (4 in.) for class 4. A band of rubber therefore always extends beyond the leather at the cuff.
Arc Flash Protection for Hands and Arms
Arc flash hand and arm protection is the subject of 130.7(C)(7)(b): hand and arm protection shall be worn where there is possible exposure to arc flash burn. The apparel described in 130.7(C)(10)(d) is required for protection of the hands from burns, and arm protection is accomplished by the apparel described in 130.7(C)(6) — the arc-rated clothing system. In other words, the shock glove and the arc protection for the hands work together: where both hazards are present, the hand needs its voltage rating and its burn protection, and neither substitutes for the other.
Maintenance and Use: Inspect Daily, Air Test Every Time
Daily inspection and the air test come from 130.7(C)(7)(c). Electrical protective equipment shall be maintained in a safe, reliable condition. Insulating equipment shall be inspected for damage before each day’s use and immediately following any incident that can reasonably be suspected of having caused damage. Insulating gloves shall be given an air test, along with the inspection: the glove is inflated and checked so that pinholes and leaks a visual pass can miss announce themselves before the glove is trusted.
The same paragraph ties use back to the class table twice: maximum use voltages for rubber insulating gloves shall not exceed those specified in Table 130.7(C)(7)(a), and the protector cuff rule from that table’s last column applies — the top of the protector’s cuff shorter than the insulating glove’s rolled cuff by at least the tabulated distance for the class.
Periodic Electrical Tests: The Two Clocks
Periodic electrical tests are required by 130.7(C)(7)(d): rubber insulating equipment shall be subjected to periodic electrical tests, with test voltages in accordance with applicable state, federal, or local codes and standards, and maximum intervals between tests not exceeding those in Table 130.7(C)(7)(b):
| Rubber insulating equipment | When to test |
|---|---|
| Gloves | Before first issue; every 6 months thereafter |
| Blankets | Before first issue; every 12 months thereafter |
| Sleeves | Before first issue; every 12 months thereafter |
| Covers | If insulating value is suspect |
| Line hose | If insulating value is suspect |
Two clocks run at different speeds — gloves on a 6-month cycle, blankets and sleeves on a 12-month cycle — while covers and line hose are tested on condition, when their insulating value is suspect. The table’s footnote adds a rule about “new” equipment that is easy to miss: new insulating equipment is not permitted to be placed into service unless it has been electrically tested within the previous 12 months, and equipment that has been issued for service is not new — it is retested on the intervals in this table. A test-date stamp on the glove is how the worker in the field verifies the clock; the employer’s certification of the testing identifies the equipment that passed and the date it was tested.
Worked Scenario
Before a justified energized diagnostic task on 4,160-volt switchgear, an electrician runs the glove routine of 130.7(C)(7) from selection to stamp. Selection first: the exposure is 4,160 volts ac, so class 0 (1,000-volt ceiling) is not enough; class 1, rated to 7,500 volts ac, is the lowest class that covers it. She takes her class 1 pair and performs the daily inspection, then the air test — and one glove leaks at a pinhole near the thumb. That pair is out of service on the spot; a pinhole found by air in the morning is exactly the failure the test exists to catch.
Her backup class 1 pair passes inspection and the air test. She checks the test stamp: tested four months ago, inside the 6-month interval — good. Protectors go on, and she verifies the fit against the table: for class 1, the top of the protector cuff sits at least 25 mm (1 in.) shorter than the rolled cuff of the rubber glove. Hands protected against both shock and the day’s handling hazards, she starts the task.
Later, a second job the same day needs fine manipulation of small test leads inside a 480-volt control section, where protectors make the work clumsy. She uses class 0 gloves without protectors — and works through the three conditions first: the task involves no activity that risks cutting or damaging the gloves; she applies the derating, one whole class, so the class 0 pair is treated as class 00 with a 500-volt ac ceiling, still above the 480-volt exposure; and when the task ends, the gloves are tagged to be electrically retested before any reuse. The exception was used — but it was used as the standard wrote it, not as a shortcut.
Common Mistakes and Safety Notes
- Skipping the air test. Visual inspection alone misses pinholes; insulating gloves get an air test along with the inspection, before each day’s use and after any incident suspected of causing damage.
- Wearing gloves past their test date. Gloves are retested every 6 months; a pair outside its interval is out of service until retested, whatever its stamp seems to say at a glance.
- Forgetting the derating when protectors come off. Class 00 drops by 50 percent; classes 0 through 4 drop one whole class — and the gloves must be electrically retested before reuse.
- Setting the protector cuff wrong. The top of the protector cuff must be shorter than the rolled top of the insulating glove cuff by at least the distance Table 130.7(C)(7)(a) gives for the class.
- Choosing a class by the voltage you expect instead of the maximum you could meet. The table’s maximum use voltage is a ceiling on exposure; the class must cover the worst voltage the hand can contact.
- Rolling up the sleeves. Sleeves must not be shortened or rolled up — that exposes skin or flammable undergarments the sleeve was issued to cover.
- Assuming brand-new gloves are ready out of the bag. New insulating equipment may not be placed in service unless it has been electrically tested within the previous 12 months.
Summary
Section 130.7(C)(7)(a) makes rubber insulating gloves with protectors the default wherever hands face electric shock from exposed energized parts, adds rubber insulating sleeves where arms are exposed too, and permits gloves without protectors only when no activity risks damaging them, they will be electrically retested before reuse, and their rating is derated — 50 percent for class 00, one whole class for classes 0 through 4. Table 130.7(C)(7)(a) caps each class: 500 volts ac for class 00 up to 36,000 volts ac for class 4, with the minimum distance between protector cuff and glove cuff growing from 13 mm to 102 mm. Section 130.7(C)(7)(b) adds arc flash protection for hands and arms. Section 130.7(C)(7)(c) requires equipment kept in a safe, reliable condition, inspected before each day’s use and after any suspect incident, with an air test for gloves. And 130.7(C)(7)(d) with Table 130.7(C)(7)(b) puts the equipment on the clock: gloves tested before first issue and every 6 months, blankets and sleeves every 12 months, covers and line hose whenever their insulating value is suspect.
Quick-Check Questions
- When may rubber insulating gloves be used without protectors?
Answer: Only when no activity performed risks cutting or damaging the glove, the gloves will be electrically retested before reuse, and the voltage rating is reduced — by 50 percent for class 00 and by one whole class for classes 0 through 4. - What are the maximum use voltages for a class 2 glove?
Answer: 17,000 volts ac (rms) and 25,500 volts dc — with the protector cuff at least 51 mm (2 in.) shorter than the glove cuff. - What two checks do insulating gloves receive before each day’s use?
Answer: An inspection for damage and an air test. - How often must rubber insulating gloves be electrically tested?
Answer: Before first issue, and every 6 months thereafter. - When are covers and line hose electrically tested?
Answer: When their insulating value is suspect — unlike gloves, blankets, and sleeves, they have no fixed calendar interval in Table 130.7(C)(7)(b).
Based on NFPA 70E (2024), Article 130, paraphrased for study.
Video lesson for this module is in production — coming soon.
Quiz for this module is being prepared.
Flashcards for this module are being prepared.



