
What you’ll learn
After this post, you will be able to determine the equivalent resistance of series and parallel combinations of elements in a simple DC circuit — using loop equations, node equations, series-parallel reduction, and Y–Δ conversion.
The toolbox chapter
Kirchhoff’s laws gave you the bookkeeping. This chapter gives you the four methods that turn those laws into answers for messy circuits: loop equations chase currents around loops, node equations solve for voltages at junctions, series-parallel reduction collapses mixed circuits to one resistor, and Y–Δ conversion untangles bridges. Every method ends the same way: check the answer against the other Kirchhoff law.
Loop equations (mesh method)
Draw the assumed current directions for each loop — a wrong guess is fine, it comes back as a negative result that is still valid. Mark the voltage polarity across each component; the current in a leg shared by two loops is expressed as a difference of the two loop currents, so no new variable is needed. KVL applies to the outer loop too: the outside loop equation is a useful cross-check on the others. Worked example from the handbook: a three-loop circuit with a 10-volt source and resistors of 1, 1, 1, 1, and 1 ohms. Loop equations: loop A: 10 = I_A + I_B; loop B: 0 = I_B + I_A + I_C; loop C: 0 = I_C + I_B. Solving the three equations gives loop currents I_A = 3.3 amperes, I_B = 1.7 amperes, and I_C = 0.9 amperes — approximately, with the handbook’s own values as given.
Node equations (nodal method)
A junction is a node; a principal node has three or more connections. Choose a reference node, the bottom wire, usually the negative terminal of a source, and set it to zero volts. Write a KCL equation per node: the currents leaving equal the currents entering, with resistors carrying the difference of the node voltages as their driving voltage. The handbook’s worked example: a three-branch circuit with a 12-volt source and resistors of 3, 2, and 4 ohms. Node equation: 12 / 3 = V / 3 + V / 2 + V / 4, giving V = 3.1 volts, or 264 / 85 if you prefer fractions. Branch currents follow from the node voltage: I1 = 3.1 / 3 = 1.03 amperes, I2 = 3.1 / 2 = 1.55 amperes, I3 = 3.1 / 4 = 0.78 amperes.
Series-parallel reduction
Apply series rules to the series parts and parallel rules to the parallel parts. In a series-parallel circuit, some resistors are in series and others are in parallel with each other or with a series combination. Work from the inside out: reduce parallel pairs to an equivalent resistance first, then add the series parts. Worked example: R1 = 6 ohms and R2 = 5 ohms in series make 11 ohms in the upper branch, in parallel with a resistor of 12 ohms. The equivalent resistance is (11 × 12) / (11 + 12) = 132 / 23 = 5.74 ohms, which is the total resistance of the series-parallel combination.
Y–Δ conversion
A T (tee) network is a Y (wye) network, and a π (pi) network is a Δ (delta) network. When a circuit has no series-parallel simplification, convert the bridge into an equivalent Y or Δ and the network becomes reducible. The formulas are: the resistance of one leg of a Y is the resistance of each leg of the Δ divided by 3, RY = RΔ / 3 for balanced networks, and the conversion between unbalanced networks uses the product-over-sum rules. Worked example: a T network with three legs of 15, 15, and 15 ohms converts to a π network with three branches of 45, 45, and 45 ohms, or the reverse, a π network of three 30-ohm branches converts to a T network of three 10-ohm legs.
Common mistakes
- “A negative current in a loop or node calculation means the circuit is impossible.” It does not — it means the current flows in the opposite direction from the one you assumed.
- “Loop equations need a new variable for each shared leg.” They do not. A shared leg’s current is the difference of the two loop currents, so no new variable is needed.
- “A reference node must be ground.” It does not need to be. It is the zero-volt reference for your equations; choose any convenient point.
- “Series-parallel reduction works on any network.” It does not. A bridge network has no series-parallel simplification until you convert it with Y–Δ.
Summary
Four methods, one discipline: loop equations chase currents around loops and use the difference in shared legs; node equations solve for voltages against a reference; series-parallel reduction collapses mixed circuits from the inside out; Y–Δ conversion untangles bridges. Check every answer against the other Kirchhoff law.
Quick-check questions
- What are the four DC circuit analysis methods?
- In a loop-current equation, how do you handle a leg shared by two loops?
- What is a reference node, and must it be ground?
- R1 = 6 ohms and R2 = 5 ohms in series, in parallel with 12 ohms — what is the equivalent resistance?
- When does series-parallel reduction fail, and what do you do instead?
Answers: 1. Loop equations, node equations, series-parallel reduction, and Y–Δ conversion. 2. Its current is the difference of the two loop currents, so no new variable is needed. 3. It is the zero-volt reference for your node equations; it does not need to be ground. 4. 5.74 ohms. 5. It fails on a bridge network; convert it with Y–Δ.
Based on DOE-HDBK-1011/92, Electrical Science, Module 2, paraphrased for study.



