
What You’ll Learn
- Why a label claiming a PPE product meets a standard is a claim — and who has to verify it
- What 130.7(C)(14) requires and how ANSI/ISEA 125 supplies the three conformity assessment methods behind it
- The difference between Level 1, Level 2, and Level 3 — self-declaration, self-declaration backed by a quality system and accredited-lab testing, and independent third-party certification
- Why the three levels are not equivalent, and how the consequence of a noncompliant product should drive the level you demand
- Why counterfeit and substandard PPE is a conformity problem, not just a purchasing problem
A Claim Is Not a Proof
An arc-rated shirt, a pair of rubber insulating gloves, a face shield — each is sold with a claim that it meets a product performance standard. A conformity assessment is the process that stands behind that claim: the way someone checks, documents, and vouches for the fact that the product actually does what the standard requires. Annex H.4 exists because the claim alone is not enough. Conformance to the performance standards referenced in Informative Annex A is what keeps the residual risk of electrical work at an acceptable level, and the annex is blunt about who carries the burden: verifying conformance is the responsibility of the employer, the purchaser, or whoever provides the PPE to employees. Buying the gear does not transfer that duty to the seller.
The Rule Behind the Levels: 130.7(C)(14) and ANSI/ISEA 125
Section 130.7(C)(14) requires PPE provided by a supplier or manufacturer to conform to the appropriate product standards by one of three methods. The methodology itself comes from ANSI/ISEA 125, the American National Standard for Conformity Assessment of Safety and Personal Protective Equipment. That standard sets criteria for products sold with claims of compliance, covering how data is collected, how products are verified, how quality and manufacturing production are controlled, and what roles suppliers, testing organizations, and third-party certification organizations each play. One practical point shapes every purchase: the conformity level for an item can be set by the manufacturer, or it can be mandated by the purchaser. An employer who wants a higher level does not have to accept whatever the supplier chose — the employer can specify it. And even then, delivery of a conformity method does not end the employer’s job. The employer still has to be able to judge which standard applies to the equipment, whether the claim of compliance is correct, and whether the test results behind it are valid — which sometimes means specifying exactly which standards a purchase must comply with.
Level 1: The Supplier Declares It
Level 1 conformity is a self-declaration. The supplier or manufacturer states that the product meets every requirement of the standard or standards it claims conformance to, and backs that statement with a supplier’s Declaration of Conformity for each product, which must be available for examination on request. Nothing outside the supplier’s own organization checks the claim. Level 1 resembles the Declaration of Conformity system used in the European Union, with one critical difference: in the EU, that declaration is a legal document tied to the governing laws of the country, while Level 1 under ANSI/ISEA 125 is not tied to a legal system and carries no external oversight. The declaration is only as good as the supplier behind it, and determining whether it is valid is the employer’s responsibility.
Level 2: Self-Declaration with a Quality System and Accredited Testing
Level 2 conformity starts from the same self-declaration, then adds two supports underneath it. First, the supplier or manufacturer operates under a registered ISO 9001 quality management system, or an equivalent system — evidence that production is controlled and repeatable, not improvised batch to batch. Second, all of the testing behind the claim was carried out by a testing laboratory accredited to ISO 17025, the standard for laboratory competence. A Declaration of Conformity for each product is still required and still must be available on request. One caution is built into the annex’s discussion of this level: an accredited laboratory is not automatically an independent one. A company with an ISO-registered quality system can run its own on-site laboratory, accredited for the testing, evaluating its own products with no external party in the room. Level 2 proves the testing was done competently and under a managed system; it does not prove the tester had no stake in the result. Judging the declaration’s validity remains the employer’s job.
Level 3: Independent Third-Party Certification
Level 3 conformity moves the judgment outside the supplier entirely. Products are certified by an independent third-party certification organization accredited to ISO 17065, the standard for bodies that certify products. At this level the certification organization directs all of the product testing, and any change to the product afterward has to go back to that organization for review and, where necessary, retesting — the supplier cannot quietly alter a certified product and keep trading on the certificate. Compliant products receive a Declaration of Conformity issued by the certification organization itself, and the products carry that organization’s mark or label, so the certification is visible on the gear, not just in a file. Within the United States, OSHA runs a process for accrediting organizations to evaluate equipment against specific standards, and equipment evaluated under that system is treated as listed within NFPA 70E.
| Level | Who declares or certifies | Quality system required | Who tests | External oversight |
|---|---|---|---|---|
| Level 1 | Supplier or manufacturer (self-declaration) | None specified | Not specified — supplier’s own claim | None |
| Level 2 | Supplier or manufacturer (self-declaration) | Registered ISO 9001 or equivalent | ISO 17025 accredited laboratory (may be in-house) | Accredited testing, but lab need not be independent |
| Level 3 | Independent ISO 17065 certification organization | Certification scheme controlled by the certifier | Testing directed by the certifier | Full — product changes reviewed, retested if needed; certifier’s mark on the product |
The Levels Are Not Equivalent
Equivalence is the trap H.4.3 warns against directly: the three levels exist side by side, but they are not to be treated as interchangeable. They represent increasing rigor in how conformity is demonstrated, and the annex ties the choice to consequence. The level of rigor demanded should be based on the potential safety and health consequence of using a product that turns out not to meet its stated performance standard. Put plainly: ask what happens to the worker if this product fails to perform as claimed. If the answer is a minor inconvenience, a lower level may be defensible. If the answer is a severe burn or a fatal shock, the conformity evidence should be as strong as the consequence is grave — a higher consequence calls for a higher level of assessment.
Why This Matters: PPE That Only Has to Work Once
Counterfeit and substandard PPE is where conformity assessment stops being paperwork. When an employer authorizes energized work, the PPE is the last line of defense standing between the worker and injury or death — and unlike most safety controls, its effectiveness may not be evident at all until the moment it is called on to perform. A glove that was never properly tested looks exactly like a glove that was. That is why the annex warns employers plainly not to supply substandard, counterfeit, or inappropriate PPE: gear that does not truly meet its standard can increase the severity of an injury when an incident occurs, instead of limiting it. The level of conformity assessment behind a product is, in effect, a measure of how much reason you have to believe the gear will work on the one occasion it absolutely has to.
Worked Scenario
A safety manager is standardizing arc-rated daily wear and rubber insulating gloves for a plant that does energized diagnostics. A budget supplier offers shirts and gloves with a Declaration of Conformity on letterhead — Level 1, self-declared, no quality-system registration and no accredited test reports offered. A second supplier provides Level 2 documentation: the same declaration, an ISO 9001 registration, and test reports from an ISO 17025 accredited lab — which, on questioning, turns out to be the supplier’s own in-house laboratory. A third supplier’s gloves carry the mark of an ISO 17065 accredited certification organization, with certification the supplier cannot modify without review. The manager thinks in consequences. If a shirt’s arc rating is overstated, a worker can be badly burned; if a glove’s voltage rating is false, the result can be fatal — and neither failure would be visible before the incident. Treating the levels as equivalent because all three products “claim compliance” would ignore exactly what H.4.3 warns against. She mandates Level 3 for the gloves, accepts Level 2 for the clothing only after reviewing the actual test reports and confirming the standards and editions claimed, and documents why each level was chosen. The purchasing specification, not the supplier’s default, sets the level from then on.
Common Mistakes and Safety Notes
- Treating the three levels as equivalent. They are three different depths of evidence. The same claim of compliance means very different things at Level 1 and Level 3.
- Assuming “accredited lab” means “independent lab.” At Level 2 the ISO 17025 laboratory can be the supplier’s own in-house facility. Competent testing is not the same as disinterested testing.
- Believing a declaration ends the employer’s duty. At every level, determining the validity of the claim — the right standard, a correct claim, valid test results — stays with the employer or purchaser.
- Letting the supplier choose the level by default. The level can be mandated by the purchaser. If the consequence of failure is severe, specify the level in the purchase requirements.
- Judging PPE by appearance. A counterfeit or substandard product is usually indistinguishable by eye, and its failure only shows during the incident it was bought for.
- Keeping the declaration in a drawer, unexamined. A Declaration of Conformity must be made available for examination on request at Levels 1 and 2, and issued by the certifier at Level 3 — ask for it before the purchase, not after an injury.
Summary
Section 130.7(C)(14) requires supplier-provided PPE to conform to the appropriate product standards by one of three methods, and ANSI/ISEA 125 defines those methods as three levels of conformity assessment. Level 1 is the supplier’s self-declaration, with no external oversight. Level 2 adds a registered ISO 9001 quality system and testing by an ISO 17025 accredited laboratory — which may still be the supplier’s own lab. Level 3 places certification with an independent ISO 17065 accredited organization that directs the testing, controls product changes, issues the declaration, and marks the product. The levels are not equivalent: rigor should rise with the safety and health consequence of a noncompliant product, because PPE is the last line of defense and counterfeit or substandard gear can make an injury worse. Verifying conformance — at whichever level — remains the responsibility of the employer, purchaser, or person providing the PPE.
Quick-Check Questions
- Under 130.7(C)(14) and ANSI/ISEA 125, who can set the level of conformity assessment for an item of PPE?
Answer: The manufacturer can determine it, or the purchaser can mandate it — a buyer does not have to accept the supplier’s default level. - What distinguishes Level 2 from Level 1?
Answer: Level 2 keeps the supplier’s self-declaration but adds a registered ISO 9001 (or equivalent) quality management system and requires all testing to be done by an ISO 17025 accredited laboratory. - Does an ISO 17025 accredited laboratory at Level 2 have to be independent of the supplier?
Answer: No. The laboratory can be the supplier’s own on-site, in-house facility — accredited testing does not necessarily mean independent testing. - What does the ISO 17065 certification organization control at Level 3?
Answer: It directs all product testing, reviews any change to the product (with retesting if necessary), issues the Declaration of Conformity, and its mark or label goes on compliant products. - How should a purchaser choose among the three levels?
Answer: By consequence — the levels are not equivalent, so the rigor of conformity assessment should match the potential safety and health consequence of using a product that does not meet its claimed standard; higher consequence demands a higher level.
Based on NFPA 70E (2024), Informative Annex H, paraphrased for study.
Video lesson for this module is in production — coming soon.
Quiz for this module is being prepared.
Flashcards for this module are being prepared.



