
What you’ll learn
After this post, you will be able to calculate total resistance for a parallel circuit, and describe how current divides between parallel branches.
Many paths, one voltage
A parallel circuit gives current more than one path. Two or more components sit across the same voltage source, each branch carries its own current, and the voltage is equal throughout: V = V1 = V2 = V3. That is the mirror image of series, where the current was shared and the voltage divided.
Branch currents add up
Each branch current follows Ohm’s Law on its own: I1 = V / R1, I2 = V / R2, I3 = V / R3. The total current is the sum of the branch currents: IT = I1 + I2 + I3. Worked example: 120 volts across three parallel resistors of 15, 20, and 10 ohms. Branch currents: I1 = 120 / 15 = 8 amps, I2 = 120 / 20 = 6 amps, I3 = 120 / 10 = 12 amps. Total: IT = 8 + 6 + 12 = 26 amps. The branch with the smallest resistor carries the most current. In this example, the 10-ohm branch carries 12 amps, nearly half the total, while the 20-ohm branch carries only 6 amps.
Equivalent resistance: always smaller than the smallest branch
The equivalent resistance is the single resistance that presents the same load to the source. By adding conductances: 1 / RT = 1 / R1 + 1 / R2 + 1 / R3. Worked example: 15, 20, and 10 ohms in parallel: 1 / RT = 1 / 15 + 1 / 20 + 1 / 10 = 0.0667 + 0.05 + 0.10 = 0.2167, so RT = 1 / 0.2167 = 4.6 ohms. This is smaller than the smallest branch resistor, 10 ohms — as it always is in a parallel circuit. If the largest resistor were 25 ohms, and the smallest 20 ohms, the equivalent resistance must be less than 20 ohms.
Shortcuts for common cases
- Equal resistors in parallel: RT = R / N, where N is the number of resistors. Worked example: five 40-ohm resistors in parallel: RT = 40 / 5 = 8 ohms.
- Two unequal resistors: product over sum. Formula: RT = (R1 × R2) / (R1 + R2). Worked example: 120 ohms and 60 ohms in parallel: RT = (120 × 60) / (120 + 60) = 7,200 / 180 = 40 ohms.
- Solving for an unknown parallel resistor: to hit a target total RT with a known resistor R already in parallel, use R_unknown = (R × RT) / (R − RT). Worked example: the handbook asks what value to add in parallel to 150 ohms to reach a total of 50 ohms: R_unknown = (150 × 50) / (150 − 50) = 7,500 / 100 = 75 ohms. Note that you can only reach a target total smaller than the existing resistor — a parallel branch can only lower the total resistance.
Common mistakes
- “Parallel total resistance is bigger than the branches.” It is always smaller than any single branch resistor.
- “Adding a parallel branch lowers the total current.” It raises it. Each new branch is another path for current, so the source supplies more total current.
- “The voltage is different across each parallel branch.” It is not. The voltage is equal throughout a parallel circuit — the same source voltage across every branch.
- “The biggest branch resistor carries the most current.” It carries the least. Branch current is inversely proportional to resistance; a small resistor takes a large share.
Summary
Parallel means shared voltage and divided current. Each branch current is the voltage divided by its own resistance; the total current is the sum of branch currents. The equivalent resistance is always smaller than the smallest branch resistor.
Quick-check questions
- In a parallel circuit, is the voltage or the current the same across all branches?
- Branch currents are 3, 3, and 2 amperes. What is the total current?
- 120 volts across 15, 20, and 10 ohms in parallel — what are the branch currents and the total?
- What is the equivalent resistance in that circuit?
- Five 40-ohm lamps in parallel — what is the total resistance?
Answers: 1. The voltage is the same across all branches; the current divides. 2. 8 amperes. 3. 8, 6, and 12 amps for the branches, with a total of 26 amps. 4. 4.6 ohms. 5. 8 ohms.
Based on DOE-HDBK-1011/92, Electrical Science, Module 2, paraphrased for study.



