
What You’ll Learn
- How the sample program handles discipline: the two knowing violations it names, and the consequences an employer must fill in from its own policy
- Why the equipment section names locks, tags, and test instruments by type and model instead of describing them generally
- The review rule that keeps the program from going stale: a scheduled review not more than one year from the last
- Who must be able to vouch that the test instrument works — and where the program builds that check into both preparation and training
- The 15 recommended training topics in G.13.0, and what they reveal about what a complete lockout/tagout education covers
The Best Procedure Fails Without the Machinery Behind It
A lockout/tagout program is more than its sequence of steps. The sample program in Informative Annex G spends its opening sections on purpose, preparation, and procedure — and then, in G.10.0 through G.13.0, it turns to the machinery that keeps the procedure alive after the binder is printed: consequences for violations, standardized equipment, a scheduled review, and a defined training curriculum. These four sections are short, and they are fill-in-the-blank by design. This article explains what each blank is for and what an employer has to decide when filling it in.
Discipline: Two Violations the Program Names Outright
Section G.10.0 is the discipline section, and it names two offenses rather than speaking in generalities. First, knowingly violating the requirements of the program draws a stated disciplinary consequence. Second, knowingly operating a disconnecting means with a lockout device (or tagout device) installed draws its own stated consequence. The model text leaves the specific actions blank — the employer fills in what its own policy prescribes — but the structure carries the lesson: the consequence for defeating a lock is spelled out in advance, separately from a general program violation, because operating against an installed device is the act most likely to kill someone mid-job. Writing the consequence down before any incident also changes the enforcement conversation from a supervisor’s judgment call to a published rule everyone was trained on.
Equipment: Locks, Tags, and Instruments by Type and Model
Section G.11.0 is the equipment section, and its three blanks are unusually specific. The locks to be used are identified by type and model. The tags to be used are identified by type and model. And the test instrument or instruments to be used are identified by type and model. Standardization does real work here. When every lock on site is the specified hardware, recognition is instant — a device that does not match the standard stands out instead of blending in. When the test instrument is specified, the program can also specify how its operation is verified: the preparation section requires providing a method to determine that the test instrument is operating satisfactorily, the lockout sequence uses that check before and after absence-of-voltage testing, and the training list closes the loop by including the safe use of test instruments. An employer filling in G.11.0 is not shopping; it is fixing the short list of devices its people will be trained to recognize, apply, and trust.
Review: Never More Than a Year Apart
Section G.12.0 is the review section, and its form is two dates: when the program was last reviewed, and when it is scheduled to be reviewed again — not more than one year from the last review. The program, in other words, carries its own expiration clock. A yearly review is where the rest of the program gets re-examined against reality: disconnecting means added or removed, locks and instruments replaced, procedures that drifted in the field, incidents and near-misses since the last pass. Because the complex lockout plan incorporates the review section along with the others, the review date is also part of what a person in charge inherits when planning a complex job — a program whose review is overdue is a warning sign about everything built on it.
Training: The Fifteen Topics
Section G.13.0 closes the program with the training curriculum — recommended topics the training can include, fifteen in all:
- Recognition of lockout/tagout devices
- Installation of lockout/tagout devices
- Duty of the employer in writing procedures
- Duty of the employee in executing procedures
- Duty of the person in charge
- Authorized and unauthorized removal of locks and tags
- Enforcement of execution of lockout/tagout procedures
- Simple lockout/tagout
- Complex lockout/tagout
- Use of single-line and diagrammatic drawings to identify sources of energy
- Alerting techniques
- Release of stored energy
- Personnel accounting methods
- Temporary protective grounding equipment needs and requirements
- Safe use of test instruments
Read as a syllabus, the list maps the whole program back onto the people who run it. It starts with the hardware (recognize it, install it), assigns the roles (employer writes, employee executes, person in charge leads), covers the rules that protect the system itself (who may remove a device, how execution is enforced), teaches both procedure levels (simple and complex), and finishes with the supporting skills — reading drawings to find every source, alerting the people around the work, releasing stored energy, accounting for personnel, grounding temporarily, and using test instruments safely. An employer building a course from the blank program can lift this list as the curriculum outline and know it touches every other section.
Worked Scenario
A mid-sized fabrication plant adopts the Annex G model as its lockout/tagout program and works through the four administrative sections deliberately. For discipline, it writes in its progressive policy — and briefs every electrician that operating a disconnect against an installed lock is listed separately, with its own consequence. For equipment, it standardizes on one lock model and one tag model plant-wide, and specifies its absence-of-voltage tester by model, so the live-dead-live verification method in its procedure refers to an instrument everyone has actually handled in training. The review dates go on the program’s cover: reviewed this January, next review scheduled the following January. Training is built straight off the fifteen topics — new hires get device recognition and installation first, while experienced hands take the complex lockout and personnel accounting modules before joining multi-crew work. Eleven months later, the scheduled review catches two things the field already knew but the paper didn’t: a disconnect added during a summer expansion, and a lock model the plant had quietly substituted. Both are fixed in the program before the year is out — which is exactly what the review clock is for.
Common Mistakes and Safety Notes
- Leaving the discipline blanks vague. The model names two knowing violations — breaking program rules, and operating a disconnecting means with a device installed — and expects a stated consequence for each.
- Describing equipment generically. G.11.0 calls for locks, tags, and test instruments by type and model; standardization is what makes an unfamiliar device stand out on sight.
- Treating the review as optional housekeeping. The next review is scheduled at adoption and must fall not more than one year after the last.
- Training only on the sequence. The fifteen topics reach beyond the steps — duties of each role, drawings, stored energy, personnel accounting, grounding, and test instruments are all on the list.
- Specifying an instrument nobody is trained on. The equipment section, the preparation section’s instrument-operation check, and the training topic on safe use of test instruments are meant to describe the same device.
Summary
The last four sections of the Annex G sample program keep it enforceable, equipped, current, and taught. Discipline names two knowing violations — violating the program, and operating a disconnecting means with a lockout or tagout device installed — with employer-stated consequences for each. Equipment is standardized by type and model for locks, tags, and test instruments, which supports recognition in the field and ties the instrument named in the program to the verification steps in the procedure and the training in its use. Review is calendared: the program records its last review and schedules the next for not more than one year later. And training is defined by fifteen recommended topics that run from recognizing a device to temporary protective grounding — a curriculum that mirrors the program itself, role by role and skill by skill.
Quick-Check Questions
- What two violations does the discipline section of the sample program name?
Answer: Knowingly violating the requirements of the program, and knowingly operating a disconnecting means with a lockout (tagout) device installed. - How does the equipment section identify the locks, tags, and test instruments to be used?
Answer: By type and model, for each of the three. - What is the maximum interval between program reviews under G.12.0?
Answer: Not more than one year — the program records the last review date and schedules the next within a year of it. - Name the first and last topics on the G.13.0 recommended training list.
Answer: First, recognition of lockout/tagout devices; last, safe use of test instruments. - Why does the program specify the test instrument by model rather than saying “a suitable tester”?
Answer: So the specified instrument matches what workers are trained on and what the procedure’s verification steps assume — recognition, the operating-satisfactorily check, and the training topic on safe use all refer to the same device.
Based on NFPA 70E (2024), Informative Annex G, paraphrased for study.
Video lesson for this module is in production — coming soon.
Quiz for this module is being prepared.
Flashcards for this module are being prepared.



